1. General Introduction
Micro Motion ELITE Flow Meter is the most advanced series Coriolis meter with superior peak performance, It's the world-leading flow and density measurement devices have set the standard for superior measurement technology. It achieves superb measurement confidence with the highest immunity to fluid, process and environmental effects; improves scalability with a broad array of application coverage including hygienic, cryogenic and high-pressure; gains real-time and in-process measurement integrity assurance with Smart Meter Verification; gets unparalleled measurement sensitivity and stability.
2. Accuracy and repeatability
Performance Specification | Liquids and Slurries | Gases | ||
Standard | Optional | Standard | Optional | |
Mass/volume flow accuracy | ±0.10% of rate | ±0.05% of rate | ±0.35% of rate | ±0.25% of rate |
Mass/volume flow repeatability | ±0.05% of rate | ±0.025% of rate | ±0.20% of rate | |
Density accuracy | ±0.0005 g/cm3 (±0.5 kg/m3) | ±0.0002 g/cm3 (±0.2 kg/m3) | ||
Density repeatability | ±0.0002 g/cm3 (±0.2 kg/m3) | ±0.0001 g/cm3 (±0.1 kg/m3) | ||
Temperature accuracy | ±1℃, ±0.5% of reading | |||
Temperature repeatability | ±0.2℃ | |||
3. Flow rate for liquid measurement
Model | Nominal Line size | Maximum flow rate | ||||
inch | mm | lb/min | gal/min | kg/h | l/h | |
CMFS007 | 1/12 | DN1 | 1.50 | 0.180 | 40.9 | 40.9 |
CMFS010 | 1/10 | DN2 | 4.03 | 0.484 | 110 | 110 |
CMFS015 | 1/6 | DN3 | 12.1 | 1.45 | 330 | 330 |
CMFS025 | 1/4 | DN6 | 77.0 | 9.23 | 2,100 | 2,100 |
CMFS040 | 3/8 | DN10 | 170 | 20.4 | 4,640 | 4,640 |
CMFS050 | 1/2 | DN15 | 250 | 30.0 | 6,820 | 6,820 |
CMFS075 | 3/4 | DN20 | 460 | 55.2 | 12,500 | 12,500 |
CMFS100 | 1 | DN25 | 950 | 114 | 25,900 | 25,900 |
CMFS150 | 11/2 | DN40 | 1,980 | 237 | 54,000 | 54,000 |
CMF010 | 1/10 | DN2 | 3.96 | 0.475 | 108 | 108 |
CMF025 | 1/4 | DN6 | 79.9 | 9.58 | 2,180 | 2,180 |
CMF050 | 1/2 | DN15 | 249 | 29.9 | 6,800 | 6,800 |
CMF100 | 1 | DN20 | 997 | 120 | 27,200 | 27,200 |
CMF200 | 2 | DN50 | 3,190 | 383 | 87,100 | 87,100 |
CMF300 | 3 | DN80 | 9,970 | 1,200 | 272,000 | 272,000 |
CMF350 | 4 | DN100 | 15,000 | 1,800 | 409,000 | 409,000 |
CMF400 | 6 | DN150 | 20,000 | 2,400 | 545,000 | 545,000 |
CMFHC2 | 8 | DN200 | 54,000 | 6,440 | 1,470,000 | 1,470,000 |
CMFHC3 | 10 | DN250 | 94,000 | 11,227 | 2,550,000 | 2,550,000 |
CMFHC4 | 12 | DN300 | 120,000 | 14,350 | 3,266,000 | 3,266,000 |
4. Flow rate for gas measurement
Model | Nominal Line size | Maximum flow rate | Volume flow rate | |||
inch | mm | lb/min | kg/h | SCFM | Nm3/h | |
CMFS007 | 1/12 | DN1 | 0.5 | 15 | 12 | 20 |
CMFS010 | 1/10 | DN2 | 2 | 45 | 37 | 63 |
CMFS015 | 1/6 | DN3 | 4 | 112 | 93 | 158 |
CMFS025 | 1/4 | DN6 | 13 | 364 | 301 | 511 |
CMFS040 | 3/8 | DN10 | 29 | 796 | 659 | 1,120 |
CMFS050 | 1/2 | DN15 | 42 | 1,144 | 947 | 1,609 |
CMFS075 | 3/4 | DN20 | 80 | 2,185 | 1,808 | 3,072 |
CMFS100 | 1 | DN25 | 159 | 4,342 | 3,593 | 6,105 |
CMFS150 | 11/2 | DN40 | 330 | 8,990 | 7,440 | 12,642 |
CMF010 | 1/10 | DN2 | 1 | 34 | 28 | 48 |
CMF025 | 1/4 | DN6 | 17 | 469 | 388 | 659 |
CMF050 | 1/2 | DN15 | 44 | 1,202 | 995 | 1,691 |
CMF100 | 1 | DN20 | 196 | 5,337 | 4,417 | 7,506 |
CMF200 | 2 | DN50 | 592 | 16,108 | 13,330 | 22,651 |
CMF300 | 3 | DN80 | 1,965 | 53,501 | 44,275 | 75,234 |
CMF350 | 4 | DN100 | 3,403 | 92,682 | 76,700 | 130,332 |
CMF400 | 6 | DN150 | 4,976 | 135,507 | 112,140 | 190,553 |
CMFHC2 | 8 | DN200 | 9,212 | 250,858 | 207,600 | 352,763 |
CMFHC3 | 10 | DN250 | 16,204 | 441,248 | 365,160 | 620,496 |
CMFHC4 | 12 | DN300 | 24,555 | 668,664 | 553,360 | 940,294 |
5. Basic Code Selection of Micro Motion ELITE
Main Code | Suffix Codes | Description | ||||||||||
Sensor Series | As per flow rate type above | |||||||||||
Sensor Size | As per flow rate type above | |||||||||||
Wetted part material | M | 316L stainless steel | ||||||||||
L | 304L stainless steel | |||||||||||
H | Nickel alloy C22 | |||||||||||
Y | Super Duplex (UNS S32750) | |||||||||||
P | Nickel alloy C22/316L stainless steel | |||||||||||
A | High temperature 316L stainless steel | |||||||||||
B | High temperature nickel alloy C22 | |||||||||||
Process Connection | As per process connection table | |||||||||||
Enclosure | N | Standard case (300-series stainless steel) | ||||||||||
P | Standard case (300-Series Stainless Steel) with one (CMFS) or two (CMF) 1/2-inch NPT purge fittings | |||||||||||
J | Standard case (300-series stainless steel); with mounting bracket | |||||||||||
U | Standard case (300-Series Stainless Steel) with purge fittings (one 1/2-inch NPT female); with mounting bracket | |||||||||||
M | 316L stainless steel case | |||||||||||
Q | 316L stainless steel case; with mounting bracket | |||||||||||
K | 316L Stainless Steel Case with purge fittings (one 1/2-inch NPT female) | |||||||||||
H | 316L Stainless Steel case; Hygienic finish: 32 Ra (0.8 μm) Flow Path | |||||||||||
T | 316L Stainless Steel case; Hygienic finish: 32 Ra (0.8 μm) Flow Path; with mounting bracket | |||||||||||
Electronics | 0 | Model 2400S transmitter | ||||||||||
1 | Extended mount Model 2400S transmitter | |||||||||||
2 | 4-wire polyurethane-painted aluminum integral enhanced core processor for remote mount transmitters | |||||||||||
3 | 4-wire stainless steel integral enhanced core processor for remote mount transmitters | |||||||||||
4 | 4-wire polyurethane-painted aluminum integral extended mount enhanced core processor for remote mount transmitters | |||||||||||
5 | 4-wire extended mount stainless steel integral enhanced core processor for remote mount transmitters | |||||||||||
6 | MVDSolo; polyurethane-painted aluminum integral enhanced core processor (for OEMs) | |||||||||||
7 | MVDSolo; stainless steel integral enhanced core processor (for OEMs) | |||||||||||
8 | MVDSolo; extended mount polyurethane-painted aluminum integral enhanced core processor (for OEMs) | |||||||||||
9 | MVDSolo; extended mount stainless steel enhanced core processor (for OEMs) | |||||||||||
A | 4-wire stainless steel integral core processor for remote mount transmitters | |||||||||||
C | Model 1700/2700 transmitter | |||||||||||
H | 9-wire extended mount polyurethane-painted aluminum junction box | |||||||||||
J | 2-wire integrally mounted Model 2200S transmitter | |||||||||||
M | For integral mount standard finish FMT Filling transmitter | |||||||||||
N | For integral mount improved surface finish (64Ra) FMT Filling transmitter | |||||||||||
Q | 4-wire polyurethane-painted aluminum integral core processor forremote mount transmitters | |||||||||||
R | 9-wire polyurethane-painted aluminum junction box | |||||||||||
S | 9-wire 316L stainless steel junction box | |||||||||||
T | 9-wire extended mount stainless steel junction box | |||||||||||
W | MVDSolo; polyurethane-painted aluminum integral core processor for direct host connection (for OEMs) | |||||||||||
D | MVDSolo; stainless steel integral core processor for direct host connection (for OEMs | |||||||||||
U | 2-wire extended Model 2200S transmitter | |||||||||||
Conduct | A | 3/4-NPT with no gland with any other electronics interface | ||||||||||
B | 1/2-inch NPT, no gland | |||||||||||
E | M20, no gland | |||||||||||
F | Brass nickel cable gland | |||||||||||
G | Stainless steel cable gland | |||||||||||
H | Brass nickel cable gland | |||||||||||
J | Stainless steel cable gland | |||||||||||
K | JIS B0202 1/2G , no gland | |||||||||||
L | Japan brass nickel cable gland | |||||||||||
M | Japan stainless steel cable gland | |||||||||||
N | JIS B0202 3/4G, no gland | |||||||||||
O | Japan brass nickel cable gland | |||||||||||
P | Japan stainless steel cable gland | |||||||||||
Approval | 1 | As per explosion approval table for worldwide markets | ||||||||||
Languages | E | English installation manual | ||||||||||
M | Chinese installation manual | |||||||||||
calibration | 2 | 0.05% mass flow and 0.0005 g/cm3 (0.5 kg/m3) density calibration | ||||||||||
3 | 0.05% mass flow and 0.0002 g/cm3 (0.2 kg/m3) density calibration | |||||||||||
6 | 0.05% mass flow and 0.002 g/cm3 (2.0 kg/m3) density calibration | |||||||||||
D | 0.10% mass flow and 0.0002 g/cm3 (0.2 kg/m3) density calibration | |||||||||||
K | 0.10% mass flow and 0.0005 g/cm3 (0.5 kg/m3) density calibration | |||||||||||
C | 0.10% mass flow and 0.002 g/cm3 (2.0 kg/m3) density calibration | |||||||||||
Z | 0.10% mass flow and 0.0005 g/cm3 (0.5 kg/m3) density calibration | |||||||||||
Measure application software | A | Petroleum measurement | ||||||||||
C | Cryogenic application | |||||||||||
Z | No measurement application software | |||||||||||
Factory options | Z | Standard product | ||||||||||
X | ETO product | |||||||||||
6. Reference dimensions for CMFS models
